NaOH/Et3N-Promoted Stereoselective One-Pot Synthesis of α-Diazo Oxime Ethers via Diazo Transfer Reaction

For the first time, we have observed a combined effect of two bases NaOH/Et₃N to promote the diazo transfer reaction of β-oximino esters. This unusual synergistic effect has been employed to obtain α-diazo oxime ethers directly from β-keto esters by one-pot process. This method is simple and cost-effective and the reagents are readily available.     

Fabrication and characterization of an irradiation facility for large-sample geometry

An irradiation facility consisting of a modified beam port shielding plug has been designed, fabricated built and characterized for use in irradiating non-standard sample geometries. The shielding plug features a graphite moderator at the core end with a hole, or “well” drilled of sufficient diameter and depth to accommodate an eight ounce (227 gram) sample bottle. Added shielding behind the graphite consists of castable neutron- and -gamma-ray shielding. The modified shielding plug can be removed relatively quickly from its irradiation position to minimize personnel exposures. It is mounted in close proximity to the Ohio State University Research Reactor reactor core to allow performance of high-sensitivity neutron activation analysis studies. Using the SAND-II unfolding code, the energy-dependent neutron flux has been measured in the sample irradiation position. When operating at 100 % power, the total flux is 3.9 × 10¹² n/cm²/s. Of this, 55 % is thermal (<0.5 eV), 23 % is epithermal (>0.5 eV, <0.5 MeV), and 22 % is “fast” (>0.5 MeV). This makes the facility suitable for neutron activation studies. Recently it has been used for irradiation of filter papers collected in a study of particulate air pollution in the form of atmospheric particulate matter in an urban environment.     

Morphology of actinide-rich particles released from the BOMARC accident and collected from soil post remediation

The physical, chemical, and radiological characteristics of material released to the environment from accidents involving nuclear weapon components are dependent upon many factors, especially the manner in which the material is released and delivered to the environment. These characteristics will also be influenced by physical and chemical effects associated with weathering if the material remains exposed to the environment for a long period of time. This study evaluates the morphological characteristics of particles released to the environment as a result of the 1960 BOMARC incident and compares these characteristics to those described following similar incidents at Thule, Greenland (1968) and Palomares, Spain (1966). Each of these incidents involved unique circumstances and conditions that distributed actinide-rich particles to the environment with a range of distinctive morphological characteristics. Morphological and surface elemental analyses were conducted on a set of discrete particles isolated from samples of post-remediated soil collected at McGuire Air Force Base, the site of the BOMARC incident. Scanning electron microscopy and complimentary energy dispersive X-ray spectroscopy were used to perform the analyses. Non-destructive analysis of uranium and plutonium contained in each particle was measured using high-resolution gamma spectrometry. Unique characteristics of the BOMARC samples include some particles exhibiting a smooth, crystalline texture and varying elemental surface distribution of uranium and plutonium, dependent on the particle’s morphology.     

Surface Modification of Smectite Clay Induced by Non-thermal Gliding Arc Plasma at Atmospheric Pressure

Smectite clay from Sabga (west-Cameroon) was treated in aqueous suspension by gliding arc plasma to modify its surface properties. The evolution of the modifications was followed with the exposure time and post-discharge duration using Fourier transformed infra red spectroscopy and scanning electron microscopy. X-ray diffraction and nitrogen physisorption analyses were also performed to evaluate if both crystalline and textural properties of the material are affected by the treatment. The results obtained show that the plasma treatment causes the breakdown of structural bounds at the clay surface and induces the formation of new hydroxyl groups (Si–OH and Al–OH) on the clay edges. Crystallinity, sheet structure and textural properties are not significantly affected by the plasma treatment. However, it should be noted that an intensive treatment of the clay lowers the pH of the suspension, which subsequently induces an acid attack of the clay. In such case, the specific surface area of the clay increases. This study demonstrates that gliding arc plasma treatments can be used to activate clay minerals for environmental application.     

Volatile organic compounds in an urban environment: a comparison among Belgium,Vietnam and Ethiopia

The effects of urban and indoor air pollution on human health are a major environmental concern for all, but not much has been researched in the developing world. Specifically, quantitative data on the occurrence of volatile organic compounds (VOCs) – main contributors to air pollution – in Asia and Africa are scarce compared to the availability of data in the developed world. This paper presents one of the first studies focusing on the analysis and occurrence of VOCs in Vietnam and Ethiopia, which constitutes part of the novelty of this work. A spectrum of 34 VOCs was measured at eight different urban sites in Ghent (Belgium), Hanoi (Vietnam), Jimma and Addis Ababa (Ethiopia) during three sampling campaigns from September 2008 to September 2010. Sampling was done in an active way by means of sorbent tubes filled with Tenax TA. The analysis was done by TD-GC-MS using internal standard calibration. Data were interpreted and compared in terms of (i) individual, subgroup and total VOCs concentration (TVOCs), (ii) indoor-to-outdoor (I/O) concentration ratios, (iii) source identification by diagnostic ratio and/or correlation coefficients, and (iv) ozone formation potential (OFP) at outdoor sites based on up-to-date maximum incremental reactivity (MIR). I/O concentration ratios varied between 0.2 and 30, with big differences noticed with respect to the type of VOC(s) considered and the type of outdoor sampling location. The highest TVOC concentrations were measured in street samples with maximum values of 54?µg/m³ in Ghent, 507?µg/m³ in Hanoi and 318?µg/m³ in Addis Ababa illustrating the large difference in ambient air quality levels. This is also reflected in the arithmetic mean OFP values (µg/m³) of 82, 1308 and 596 in Ghent, Hanoi and Addis Ababa, respectively. Results of this study could be helpful to support formulation of national policy with regard to ambient air quality.     

Novel Tripod Amphiphiles for Membrane Protein Analysis

Integral membrane proteins play central roles in controlling the flow of information and molecules across membranes. Our understanding of membrane protein structures and functions, however, is seriously limited, mainly due to difficulties in handling and analysing these proteins in aqueous solution. The use of a detergent or other amphipathic agents is required to overcome the intrinsic incompatibility between the large lipophilic surfaces displayed by the membrane proteins in their native forms and the polar solvent molecules. Here, we introduce new tripod amphiphiles displaying favourable behaviours toward several membrane protein systems, leading to an enhanced protein solubilisation and stabilisation compared to both conventional detergents and previously described tripod amphiphiles.     

Understanding the acceleration in the ring-opening of lactones delivered by microwave heating

This paper reports the first detailed study focussed upon identifying the influence that microwave heating (MWH) has upon the mechanic steps involved in the tin catalysed ring-opening of lactones such as ?-caprolactone (CL). Direct comparison of conventional (CH) and microwave (MWH) heated kinetic studies showed that a key factor in the reduction of the polymerisation cycle time with MWH was the elimination of the induction period associated with in situ catalyst manufacture and initiation. NMR studies demonstrated that the most significant mechanistic change contributing to the observed induction time reduction/elimination was faster initiation (i.e., reaction of the initiatior/catalyst complex with the first monomer unit). Consequently, analysis of the dielectric properties of the reaction components predicted that this MWH induced change was related to the selective volumetric heating of both the catalyst and the monomer. Furthermore, this indication of the greater significance of the initiation step in defining the length of the induction period suggests that this is the rate determining step of the process, whether conducted by CH or MWH. Increasing the catalyst concentration was demonstrated to produce significant reductions in reaction heat-up time and to induce a significant (up to 30 °C) overshoot in reaction mixture bulk temperature in with MWH only. Thus supporting the conclusion that selective heating of the organometallic species in the system contributes directly to differences in the reaction conditions and which need to be taken into account when drawing comparisons with CH systems. Consequently, both effects were concluded to be thermally generated from selective volumetric heating.